How To Repair Small Patch Of Carpet

Download Commodity

Download Article

Patching a carpet is a chore that only about every homeowner volition confront at one fourth dimension or another. Spills, cigarette burns, and other mishaps can ruin a small-scale surface area of wall to wall rug, making it necessary to remove the section as a manner to repair the damage. Fortunately, the task of patching a damaged carpet is relatively easy and requires nothing more a little time and a few uncomplicated supplies.

1

Mensurate the damaged area of the carpet. Use the record measure to place the size of the patch that will be extracted from the surrounding rug. This will get in easier to cut a replacement patch to size.^[one]
2
Tape off the area to exist removed. Use duct tape to outline a square section to be removed. Cheque the position of the tape with the measurements taken previously to make sure the within border of the record matches those dimensions.^[two]
- Try to subcontract the replacement carpeting from an inconspicuous area, such as within a closet or underneath a bed. Be sure that the identify you farm the replacement carpet from isn't going to be visible.
- You can besides go along extra carpet in your attic or storage for repairing damaged areas.
Advertisement
3
Remove the damaged section of rug. Use a utility knife or a carpet cut tool to gently cutting along the inside border of the duct tape. Apply just enough pressure to cut through both the surface of the carpet and the backing, but not plenty to damage the underlying layer of padding. Once the department is completely cut, lift it off the carpet surface.^[iii]
- If working with a carpet cutting tool, utilize the tool to offset make an imprint. Once an imprint has been made, adhere the cutter blades and the pivot spiral and make your incision, rotating as many every bit two or iii times in order to remove it.^[4]
4

Measure and cut the replacement patch. Plow a carpet remnant face downwards and measure a patch for the carpeting, using the measurements obtained earlier as a guideline. Mark the lines of the patch with the pencil, then use a utility knife or carpet cutter to cut out the patch.
5
Fix the rug to receive the patch. Neutralize the disk temporarily by putting a minor corporeality of water on it. Lift the edges of the carpeting around the hole and slide the adhesive disk underneath, with the adhesive side facing upward.^[five]
- Make sure that the adhesive disk is significantly larger than replacement patch: you want the deejay to hold onto all of the replacement patch, especially the corners, as well every bit some surrounding carpet.
- When the patch becomes gummy over again, in almost 3 to v minutes, press downward on the outer edge of the carpet to secure it into place.
6
Move the carpeting patch into position. Groom abroad any loose carpeting fibers from the edge of the hole. Check the fit earlier applying whatsoever glue. And so, put downwardly a thin layer of carpet gum along the edges of the adhesive disk. Place the patch into the hole, taking intendance to make sure the fit is snug and even. Press lightly to permit the bankroll on the patch to come up into contact with the underlying tape and attach properly.^[6]
- Align the patch so that the direction of the fibers in the patch match the direction of the fibers in the remainder of the rug.
- You have virtually xv minutes to position and align the patch perfectly earlier the glue sets, permanently anchoring your patch in identify. Work speedily.
7
Smooth the pile of the carpet to hibernate the seams of the patch. Depending on the blazon of pile, this may be accomplished by brushing the fingers around the perimeter of the patch, or using a carpet brush to train the pile on the patch to move in the same direction as the remainder of the carpet pile.
- You tin can also vacuum the department with an agitator attachment to lift up the pile.
Advertisement

1
Measure the damaged expanse of the carpeting. Determine the size of the carpet to be cut out, and whether you want to cutting a rectangular or round replacement patch to fill the expanse in.
- Rectangular patches can exist cut using a utility knife, while circular patches can be cut using a circular rug cutter.
2
Remove the damaged section of carpeting. Use a utility pocketknife or a rug cut tool to gently cutting away the rug. Apply just enough pressure to cut through both the surface of the carpet and the backing, but non plenty to damage the underlying layer of padding. In one case the section is completely cut, elevator it off the rug surface.
- You may desire to save the damaged section in case you need to patch a smaller area that can be cut from this section.
three

Mensurate and cutting the replacement patch. Plough a carpet remnant face down and mensurate a patch for the carpeting, using the measurements obtained earlier as a guideline. Or remove a piece of rug from an camouflaged area, such every bit the inside of a closet. Marking the lines of the patch with the pencil, and so utilize a utility knife or carpeting cutter to cut out the patch.
iv

Wet the carpeting patch pad. Carpeting patch pads are used to iron on especially made adhesive disks that activate with the help of estrus. Your carpeting patch pad may exist aluminum-sided on the pinnacle and contain a previous material on the bottom. Wet your carpet patch pad under h2o and wring out the excess; the pad should be damp but not dripping.
5

Slide the adhesive pad underneath the cut-out carpet, centering it. Make sure the adhesive pad is adequately bigger than the patch, particularly fabricated for heat-application, and centered for even distribution. Smooth out whatever wrinkles if necessary
half-dozen

Identify the replacement patch onto the agglutinative disk. Go over the patch with a carpet castor to remove loose fibers. Make sure that the direction of the fibers on the patch matches the direction of the fibers on the rug.
vii

Place the patch pad on top of the patch, aluminum side up. Brand sure the patch pad is centered and you know where the patch is underneath.
8
Using an atomic number 26 assault high, estrus the patch pad up for one minute. Printing down on the iron and then that the heat transfers from the patch pad, through the carpeting, to the adhesive pad underneath. Remember that the adhesive pad activates when subjected to rut.
- Y'all should hear a calorie-free sizzle when you touch the iron onto the patch pad. This is the water reacting to the heat, not the carpeting called-for.
- If the patch is large, get over different spots the patch with the iron — enough to cover the entire patch. You don't desire to neglect to activate the head beneath the patch.
9

Remove the iron and patch pad permit the area cool. The glue on the adhesive pad won't fully dry until the rug is absurd. Go over the patch with a carpeting brush and remove whatever loose fibers from the edge of the carpet.

Ad

Add New Question

Question

From where tin can I get the rug patch pad?

Sara Mancilla

Community Answer

Information technology is available at near home improvement stores, such equally The Dwelling Depot or Lowe'south.
Question

How do I gear up a small hole in my carpet?

Josh Nolan

Community Answer

If information technology'due south a cut pile plush, it should be fairly easy. Using balance rug from the install or corner of closet or obscure area, cut a piece the estimate size of the hole. Using gorilla glue from Abode Depot and a really sharp pair of scissors or razor blade, cut to fit and carefully glue the perimeter of the bankroll of the carpet. Place the donor piece in identify and put a book over it until it dries. Using your scissors, brush the carpet dorsum and forth and trim whatever taller tufts until it looks even. Bonus: for color difference, typically from clothing or soil from foot traffic, spray a little Folex on the patch and surrounding surface area and scrub until the colors blend.
Question

What if the damaged carpeting abuts a door frame?

Josh Nolan

Customs Answer

Watch out for the tack strip! It has sharp nails. Cut the donor carpet to friction match and glue the perimeter of the rug backing with gorilla glue. Careful! A little goes a long style. Put the patch piece in identify and cut as necessary. Lightly tap down the carpet onto the tack strip by the door frame. Constrict in place to the door frame, trim, or wall.

Inquire a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

If carpet tape is not doing the job, y'all tin as well apply carpeting glue to hold the patch in position. A line or 2 of glue on the surface of the rug pad will oftentimes be sufficient. Keep in mind that if you program on replacing the carpeting, the patch will adhere to the padding, making it harder to salvage the pad.
Install a new blade in the utility pocketknife before attempting to brand any cuts. This will get in easier to achieve even edges that friction match up well, rather than possibly creating small gaps betwixt the patch and the hole in the rug.^[7]
Utilise both hands when cutting the carpet to avert slipping and cut one hand. You lot can too keep one manus higher up the blade when cutting, then that if you skid, the hand is not in the direction of the blade.^[8]
Y'all can employ a length of flat metallic as a weight and for a straight edge during cut.

Thanks for submitting a tip for review!

Things Yous'll Need

Carpet remnant
Pencil
Duct tape
Carpet record
Adhesive disk
Utility knife or carpeting cutter
Tape mensurate

About This Commodity

Article Summary X

To patch carpeting using a patch repair kit with adhesive disks, starting time measure the damaged area of the rug and identify duct tape around information technology. And so, use a utility knife to cut forth the inside of the tape. Next, measure and cut the replacement patch. Once you have the replacement piece fix, slide the adhesive disk under the edges of the rug surrounding the hole to proceed it in identify. Finally, press the new patch of rug onto the agglutinative. To learn how to employ a patch repair kit with heat, go on reading!

Did this summary aid you?

Thanks to all authors for creating a page that has been read 308,092 times.

Did this article help you?